UL iQ™ for Appliance Wiring Materials

	
                            APPLIANCE WIRING MATERIAL
                        
                            Subj.758
                        
                            Section
                            2
                        
                            Page
                            2627
                        
                            Issued:1973-04-24
                    
                            Revised:2011-11-03
                    
                            Style
                            2627
                        
                            Multiconductor cable with extruded non-integral jacket.
                    
			Rating80 deg C, Voltage not specified, Horizontal flame (construction A) Cable flame (construction B).
		
			Conductor32 AWG - 20 AWG, solid or stranded, copper, copper-clad steel, copper alloy, bare, tinned or silver-coated, having a minimum of 40 percent conductivity.
		
			InsulationExtruded XLPE or extruded foamed XLPE, 15 mils thickness.
		
			AssemblyMultiple conductors. Over the conductors shall be applied a spiral wrap of XLPE or foamed XLPE thread nominally 15 mils in diameter, approximately 1/2 inch between turns. This assembly shall be enclosed with an XLPE or foamed XLPE tube having an approximate 15 mils thickness. Over this is applied a wrap of aluminum-faced PET tape with a drain wire under the tape. The length of lay of the twisted conductors is not specified. Fillers may be used in a cable but are not required. A barrier layer, if employed, may be a fibrous wrap serving or braid; paper; nylon; PET; or a thermoplastic-tape wrap. Such a barrier layer would serve to protect the cable during further processing and would be applied immediately over the twisted assembly of individual conductors or groups of conductors.
		
			ShieldOptional.
		
			JacketExtruded PVC.
		
			Construction A
		
			Diameter of core assembly under jacketMinimum average thicknessMinimum thickness at any point
		
			0.425 inch or less35 mils28 mils
		
			0.526-0.700 inch60 mils48 mils
		
			0.701-1.500 inch80 mils64 mils
		
			1.501-2.500 inch110 mils88 mils
		
			2.501 inch and larger140 mils112 mils
		
			#Construction B, , ; Diameter of core assembly under jacket, Minimum average thickness, Minimum thickness at any point; 0.700 inch or less, 60 mils, 48 mils; 0.701-1.500 inch, 80 mils, 64 mils; 1.501-2.500 inch, 110 mils, 88 mils; 2.501 inch and larger, 140 mils, 112 mils#
		
			StandardAppliance Wiring Material UL 758.
		
			MarkingGeneral.
		
			Use- Construction A - Internal wiring. - Construction B - External wiring.
		
                UL and the UL Logo are trademarks of UL LLC © 2024

Subj.758	Section 2	Page 2627	Issued:1973-04-24
			Revised:2011-11-03


Rating	80 deg C, Voltage not specified, Horizontal flame (construction A) Cable flame (construction B).

Conductor	32 AWG - 20 AWG, solid or stranded, copper, copper-clad steel, copper alloy, bare, tinned or silver-coated, having a minimum of 40 percent conductivity.

Insulation	Extruded XLPE or extruded foamed XLPE, 15 mils thickness.

Assembly	Multiple conductors. Over the conductors shall be applied a spiral wrap of XLPE or foamed XLPE thread nominally 15 mils in diameter, approximately 1/2 inch between turns. This assembly shall be enclosed with an XLPE or foamed XLPE tube having an approximate 15 mils thickness. Over this is applied a wrap of aluminum-faced PET tape with a drain wire under the tape. The length of lay of the twisted conductors is not specified. Fillers may be used in a cable but are not required. A barrier layer, if employed, may be a fibrous wrap serving or braid; paper; nylon; PET; or a thermoplastic-tape wrap. Such a barrier layer would serve to protect the cable during further processing and would be applied immediately over the twisted assembly of individual conductors or groups of conductors.

Shield	Optional.

Jacket	Extruded PVC.
	Construction A
	Diameter of core assembly under jacket	Minimum average thickness	Minimum thickness at any point
	0.425 inch or less	35 mils	28 mils
	0.526-0.700 inch	60 mils	48 mils
	0.701-1.500 inch	80 mils	64 mils
	1.501-2.500 inch	110 mils	88 mils
	2.501 inch and larger	140 mils	112 mils
	#Construction B, , ; Diameter of core assembly under jacket, Minimum average thickness, Minimum thickness at any point; 0.700 inch or less, 60 mils, 48 mils; 0.701-1.500 inch, 80 mils, 64 mils; 1.501-2.500 inch, 110 mils, 88 mils; 2.501 inch and larger, 140 mils, 112 mils#

Standard	Appliance Wiring Material UL 758.

Marking	General.

Use	- Construction A - Internal wiring. - Construction B - External wiring.