UL iQ™ for Appliance Wiring Materials

	
                            APPLIANCE WIRING MATERIAL
                        
                            Subj.758
                        
                            Section
                            2
                        
                            Page
                            2630
                        
                            Issued:1973-05-22
                    
                            Revised:2018-03-07
                    
                            Style
                            2630
                        
                            Multi-Conductor Cable with Non-Integral Extruded Jacket.
                    
			Rating90 deg C, 125 Vac, Cable Flame.
		
			Conductor30-9 AWG, Solid or Stranded Round.
		
			InsulationComplying with manufacturer's AWM Procedure.
		
			AssemblyTwo or more individually insulated conductors or groups of insulated conductors cabled together. All conductors in any group twisted together. If more than one group is used, groups shall also be twisted together. The length of lay of the twisted conductors or groups is not specified. Fillers may be used in a cable but are not required. A barrier layer, if employed, may be a fibrous wrap serving, or braid; paper; nylon; oriented polyethylene terephthalate; or thermoplastic-tape wrap. Such a barrier layer would serve to protect the cable during further processing and would be applied immediately over the twisted assembly of individual conductors or groups of conductors or over the shield, if provided.
		
			ShieldOptional - 36-30 AWG, tinned or untinned copper applied as a wrap or braid or a wrap of aluminum-faced Polyester tape. An uninsulated drain wire may be used. The shield may be over one or more of the insulated conductors or applied between the conductor assembly and the optional covering.
		
			CoveringOptional - A nominal 15 mil PVC covering may be extruded over the conductor assembly.
		
			JacketPVC
		
			dia in inchesmils min averagemils min at any point
		
			0.425 or less30 avg24 min
		
			0.425 to 0.700 dia45 avg36 min
		
			0.701 to 1.000 dia60 avg48 min
		
			1.001 to 1.500 dia80 avg64 min
		
			StandardAppliance Wiring Material UL 758.
		
			MarkingGeneral.
		
			UseExternal Interconnection or Internal Wiring of Electronic Equipment.
		
                UL and the UL Logo are trademarks of UL LLC © 2024

Subj.758	Section 2	Page 2630	Issued:1973-05-22
			Revised:2018-03-07


Rating	90 deg C, 125 Vac, Cable Flame.

Conductor	30-9 AWG, Solid or Stranded Round.

Insulation	Complying with manufacturer's AWM Procedure.

Assembly	Two or more individually insulated conductors or groups of insulated conductors cabled together. All conductors in any group twisted together. If more than one group is used, groups shall also be twisted together. The length of lay of the twisted conductors or groups is not specified. Fillers may be used in a cable but are not required. A barrier layer, if employed, may be a fibrous wrap serving, or braid; paper; nylon; oriented polyethylene terephthalate; or thermoplastic-tape wrap. Such a barrier layer would serve to protect the cable during further processing and would be applied immediately over the twisted assembly of individual conductors or groups of conductors or over the shield, if provided.

Shield	Optional - 36-30 AWG, tinned or untinned copper applied as a wrap or braid or a wrap of aluminum-faced Polyester tape. An uninsulated drain wire may be used. The shield may be over one or more of the insulated conductors or applied between the conductor assembly and the optional covering.

Covering	Optional - A nominal 15 mil PVC covering may be extruded over the conductor assembly.

Jacket	PVC
	dia in inches	mils min average	mils min at any point
	0.425 or less	30 avg	24 min
	0.425 to 0.700 dia	45 avg	36 min
	0.701 to 1.000 dia	60 avg	48 min
	1.001 to 1.500 dia	80 avg	64 min

Standard	Appliance Wiring Material UL 758.

Marking	General.

Use	External Interconnection or Internal Wiring of Electronic Equipment.