UL iQ™ for Appliance Wiring Materials

	
                            APPLIANCE WIRING MATERIAL
                        
                            Subj.758
                        
                            Section
                            4
                        
                            Page
                            4443
                        
                            Issued:1995-12-06
                    
                            Revised:2011-11-30
                    
                            Style
                            4443
                        
                            Multiple-conductor cable using non-integral jacket
                    
			Rating75 deg C, 2000 Vac, Horizontal flame, Moisture Resistant 75 deg C, sunlight resistant (optional).
		
			Conductor8 AWG - 4/0 AWG, solid or stranded.
		
			InsulationLabeled or complying with manufacturer's AWM procedure, 60 mils minimum average thickness, 54 mils minimum thickness at any point.
		
			AssemblyThree or four 8-4/0 AWG power conductors twisted together with two 10-14 AWG control wires added. Each control conductor shall be in a separate interstice between the power conductors. The maximum length of lay shall be 21 times the diameter of the power conductor for assemblies having 3 power conductors and 23 times the diameter for assemblies with 4 power conductors. The direction of length of lay shall be left hand. Nonhydroscopic fillers shall be provided as needed to ensure that the finished cable is round. The jacket may be applied in one or two layers. If applied in two layers, the outer jacket shall constitute at least 50% of the total jacket thickness. Single or two-layer jackets shall be reinforced by two servings or a braid of a suitable natural or synthetic material. The dia of the reinforcing shall not be greater than 35 mils. If two servings are used, they shall be applied in opposite directions of lay. The reinforcing material shall be under the single layer jacket and under or between the layers of a two-layer construction.
		
			CoveringOptional nonmetallic braid, type, or wrap may be employed.
		
			JacketExtruded CP or Extruded CPE or Extruded NBR/PVC, 141 mils minimum average thickness, 113 mils minimum thickness at any point.
		
			StandardAppliance Wiring Material UL 758.
		
			MarkingOptional Markings - "-50 deg. C", "Sunlight Resistant".
		
			UseExternal connection of electronic equipment where the acceptability of the combination is to be accepted by Underwriters Laboratories Inc.
		
                UL and the UL Logo are trademarks of UL LLC © 2024

Subj.758	Section 4	Page 4443	Issued:1995-12-06
			Revised:2011-11-30


Rating	75 deg C, 2000 Vac, Horizontal flame, Moisture Resistant 75 deg C, sunlight resistant (optional).

Conductor	8 AWG - 4/0 AWG, solid or stranded.

Insulation	Labeled or complying with manufacturer's AWM procedure, 60 mils minimum average thickness, 54 mils minimum thickness at any point.

Assembly	Three or four 8-4/0 AWG power conductors twisted together with two 10-14 AWG control wires added. Each control conductor shall be in a separate interstice between the power conductors. The maximum length of lay shall be 21 times the diameter of the power conductor for assemblies having 3 power conductors and 23 times the diameter for assemblies with 4 power conductors. The direction of length of lay shall be left hand. Nonhydroscopic fillers shall be provided as needed to ensure that the finished cable is round. The jacket may be applied in one or two layers. If applied in two layers, the outer jacket shall constitute at least 50% of the total jacket thickness. Single or two-layer jackets shall be reinforced by two servings or a braid of a suitable natural or synthetic material. The dia of the reinforcing shall not be greater than 35 mils. If two servings are used, they shall be applied in opposite directions of lay. The reinforcing material shall be under the single layer jacket and under or between the layers of a two-layer construction.

Covering	Optional nonmetallic braid, type, or wrap may be employed.

Jacket	Extruded CP or Extruded CPE or Extruded NBR/PVC, 141 mils minimum average thickness, 113 mils minimum thickness at any point.

Standard	Appliance Wiring Material UL 758.

Marking	Optional Markings - "-50 deg. C", "Sunlight Resistant".

Use	External connection of electronic equipment where the acceptability of the combination is to be accepted by Underwriters Laboratories Inc.