UL Certification: E41938 - Component

iq.ul.com

	CLICK TO CONTINUEView additional material information including performance and processing data	The information presented on the UL Prospector datasheet was acquired by UL Prospector from the producer of the material. UL Prospector makes substantial efforts to assure the accuracy of this data. However, UL Prospector assumes no responsibility for the data values and strongly encourages that upon final material selection, data points are validated with the material supplier.

Component - Plastics		E41938
Guide Information	View Certificate of Compliance
CELANESE INTERNATIONAL CORP
8040 DIXIE HWY, FLORENCE KY 41042-2904
FR530(l)(+)(f1), FR530L(l)(+)(f1)
Polyethylene Terephthalate (PET), glass reinforced, flame retardant "Rynite", furnished as pellets [contains mechanically recycled content]

Attention Materials Users! This product Certification has been changed on 2023-02-16; UL94 Flame class has been revised click here to learn more

Comparative Tracking Index (CTI):	2	Inclined Plane Tracking (IPT) kV:	-
Dielectric Strength (kV/mm):	34	Volume Resistivity (10^x ohm-cm):	16
High-Voltage Arc Tracking Rate (HVTR):	1	Surface Resistivity (10^x ohms/square):	-
Dimensional Change (%):	0	High Volt, Low Current Arc Resis (D495):	6

(+) -	Virgin and regrind up to 50% by weight inclusive, have the same basic material characteristics.
(f1) -	Suitable for outdoor use with respect to exposure to Ultraviolet Light, Water Exposure and Immersion in accordance with UL 746C.
(l) -	Recognized ground insulation component at 0.4 mm with MW79 in UL1446 Class 155 electrical insulation system designated R201N (File E69939).
NOTE -	(1) Material designations that are color pigmented may be followed by suffix letters and numbers. (2) Material designations may be prefixed by "ZYT" for Zytel or "MIN" for Minlon or "CRA" for Crastin or "RYN" for Rynite.
ANSI/UL 94 small-scale test data does not pertain to building materials, furnishings and related contents. ANSI/UL 94 small-scale test data is intended solely for determining the flammability of plastic materials used in the components and parts of end-product devices and appliances, where the acceptability of the combination is determined by UL.

Report Date:	1996-01-04	© 2024 UL Solutions
Last Revised:	2023-02-17

IEC and ISO Test Methods
Test Name	Test Method	Units	Thk (mm)	Value
Flammability	IEC 60695-11-10, IEC 60695-11-20	Class (color)	0.35	V-0 (NC, BK)
			0.75	V-0 (ALL)
			1.5	V-0, 5VA (NC, BK)
			2.0	V-0, 5VA (ALL)
			3.0	V-0, 5VA (ALL)
Glow-Wire Flammability (GWFI)	IEC 60695-2-12	°C	0.75	960
			1.5	960
			2.0	960
			3.0	960
Glow-Wire Ignition (GWIT)	IEC 60695-2-13	°C	0.75	800
			1.5	800
			2.0	985
			3.0	985
IEC Comparative Tracking Index	IEC 60112	Volts (Max)	-	-
IEC AC Dielectric Strength (AC DS)	IEC 60243-1	kV/mm	-	-
IEC DC Dielectric Strength (DC DS)	IEC 60243-2	kV/mm	-	-
IEC Volume Resistivity (VR)	IEC 62631-3-1	10^x ohm-m	-	-
IEC Surface Resistivity (SR)	IEC 62631-3-2	10^x ohms	-	-
IEC Inclined Plane Tracking (IPT)	IEC 60587	kV	-	-
IEC Ball Pressure	IEC 60695-10-2	°C	-	245
ISO Heat Deflection (1.80 MPa)	ISO 75-2	°C	-	-
ISO Tensile Strength	ISO 527-2	MPa	-	-
ISO Flexural Strength	ISO 178	MPa	-	-
ISO Tensile Impact	ISO 8256	kJ/m²	-	-
ISO Izod Impact	ISO 180	kJ/m²	-	-
ISO Charpy Impact	ISO 179-1	kJ/m²	-	-