iq.ul.com
CLICK TO CONTINUEView additional material information including performance and processing data The information presented on the UL Prospector datasheet was acquired by UL Prospector from the producer of the material. UL Prospector makes substantial efforts to assure the accuracy of this data. However, UL Prospector assumes no responsibility for the data values and strongly encourages that upon final material selection, data points are validated with the material supplier.
Component - PlasticsE121855
Guide InformationView Certificate of Compliance
FORMEX, DIV OF ILLINOIS TOOL WORKS INC
425 N Gary Ave, Carol Stream IL 60188
Formex CND-(b)(e)(k)(L)(f2)
Polycarbonate (PC), furnished as Multiple Layers of Sheets

Color		Min. Thk
(mm)		Flame
Class
HWI
HAI		RTI Elec
(°C)		RTI Imp
(°C)		RTI Str
(°C)
NC, BK0.16VTM-04180-80
0.19VTM-04180-80
0.25VTM-04180-80
Comparative Tracking Index (CTI):3Inclined Plane Tracking (IPT) kV:-
Dielectric Strength (kV/mm):42Volume Resistivity (10x ohm-cm):16
High-Voltage Arc Tracking Rate (HVTR):1Surface Resistivity (10x ohms/square):-
Dimensional Change (%):-High Volt, Low Current Arc Resis (D495):-
(L) - Meets the requirements for Reinforced Insulation and Supplementary Insulation requirements in IEC60950-1 , IEC62368-1, IEC61558-1, IEC60065 and IEC61347-1 at thicknesses between 0.16 mm and 0.25 mm inclusive
(b) - May have additional suffix letter(s) indicating color.
(e) - Meets the requirements for IEC 60950-1, IEC 61558-1 Mandrel Test at 0.16 mm, 0.19 mm and 0.25 mm thickness at 7KvAC
(f2) - Subjected to one or more of the following tests: Ultraviolet Light, Water Exposure or Immersion in accordance with UL 746C, where the acceptability for outdoor use is to be determined by UL.
(k) - Complies with the IEC 60695-11-5, 12 mm Flame Test (60 Sec flame duration).
NOTE - HVTR, CTI and D495 are not dependent on thickness
ANSI/UL 94 small-scale test data does not pertain to building materials, furnishings and related contents. ANSI/UL 94 small-scale test data is intended solely for determining the flammability of plastic materials used in the components and parts of end-product devices and appliances, where the acceptability of the combination is determined by UL.
Report Date:2015-10-20© 2024 UL Solutions
Last Revised:2024-10-25
 
IEC and ISO Test Methods
Test NameTest MethodUnitsThk (mm)Value
FlammabilityISO 9773Class (color)0.16VTM-0 (NC, BK)
0.19VTM-0 (NC, BK)
0.25VTM-0 (NC, BK)
Glow-Wire Flammability (GWFI)IEC 60695-2-12°C--
Glow-Wire Ignition (GWIT)IEC 60695-2-13°C--
IEC Comparative Tracking IndexIEC 60112Volts (Max)--
IEC AC Dielectric Strength (AC DS)IEC 60243-1kV/mm--
IEC DC Dielectric Strength (DC DS) IEC 60243-2kV/mm--
IEC Volume Resistivity (VR)IEC 62631-3-110x ohm-m--
IEC Surface Resistivity (SR)IEC 62631-3-210x ohms--
IEC Inclined Plane Tracking (IPT)IEC 60587kV--
IEC Ball PressureIEC 60695-10-2°C--
ISO Heat Deflection (1.80 MPa)ISO 75-2°C--
ISO Tensile StrengthISO 527-2MPa--
ISO Flexural StrengthISO 178MPa--
ISO Tensile ImpactISO 8256kJ/m2--
ISO Izod ImpactISO 180kJ/m2--
ISO Charpy ImpactISO 179-1kJ/m2--